*************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : 2.5.9.1 Release Date : October 25, 2005 Applied Models : Vigor2500V series ( Vigor2500V, Vigor2500Vi, Vigor2510V, Vigor2510Vi) *************************************************************************************** Note : The RST file will clear out all existing router settings back to factory defaults. You must use the RST file if you are experience unusual results after upgrading with the ALL file. Do not then attempt to restore old settings from a backup file made with from previous firmware. After upgrading, please check that your web configurator shows the firmware version/build listed above. multi-PVC support shall be referred to ISP services. You are recommended not to use this portion if your ISP did not support multi-PVC. You are recommended to select "UBR" of QoS for internet Access if you only use one PVC to access internet. [release]: the same firmware for annex A and B 1> "v25vc259.xxx" is with Conexant modem code v3.27. ( recommended for annex A [POTS] ) 2> "v25vo259.xxx" is with Conexant modem code v3.20. ( recommended for annex B [ISDN], Netherlands, Spain, and so on ) ( For annex A, US, China ) 3> "v25va259.xxx" is with Conexant modem code v3.46. ( For Poland or Try this if you have sync problem on adsl. ) 4> "v25vt259.xxx" is with Conexant modem code v3.50. ( Try this if you have sync problem adsl) Notes: 1. Please select modulation to "MULTI" or "T1.413" when your adsl line was annex B ( ADSL Over ISDN) and it only can work with Alcatel ETSI Mode. 2. Please try to use modem code v3.20 if you meet sync problem. [1. New Features] - Add telnet command to set QoS bandwidth. (adsl txpct). - Add telnet command to set timeout of collecting phone number when you want to make a phone call. [2. Enhancement] - PPPoE maybe not recovery even the ADSL physical link online again after the ISDN Backup take over the WAN connection. - Add PPPoE setting in UK version. - Resolved the Web Browers maybe slow in MAC os issue. - Change VPI/VCI settings for Nokia linecards in Norway. - Adsl sync speed in Portugal enhance. *************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : 2.5.9 Release Date : August 31, 2005 Applied Models : Vigor2500V series ( Vigor2500V, Vigor2500Vi, Vigor2510V, Vigor2510Vi) *************************************************************************************** [1. New Features] - Add Supplementary Services. - Tone setting for Portugal and Sweden. - DTMF Caller ID Type for Denmark, Netherlands, Spain and Finland [2. Enhancement] - Emule/BT maybe cause the device reboot. - MPoA Pure Bridge Mode didn't work issue. - Stun Server doesn't work when use ISDN. - Fixed the ISDN Remote Activation Function doesn't work issue. - Uncorrect Tone when use DrayTel. - Be unable to drop PPPoE on the Online Status. - Re-align the VoIP DialPlan Configuration. - SIP register problem when use ISDN for Internet access. - VoIP Can't Register via ISDN. - Call Waiting mode issue. - Call Transfer issue. - The WUI slow issue on MAC OS X. - Uncorrect default settings of DoS when click "Clear All" button. - The caller cannot hear the person who uses the standard codec G.729a/b. - Can't dial extension number or hear busy tone when select OutBand DTMF tone. - The Backup Phone Number of DialPlan can not be saved. ******************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : 2.5.8.2 Release Date : June 28, 2005 Applied Models : Vigor2500V series ( Vigor2500V, Vigor2500Vi, Vigor2510V, Vigor2510Vi) ******************************************************************************************** [Enhancement] - ISDN dial must dial twice issue. ******************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : 2.5.8.1 Release Date : June 16, 2005 Applied Models : Vigor2500V series ( Vigor2500V, Vigor2500Vi, Vigor2510V, Vigor2510Vi) ******************************************************************************************** [Enhancement] - Some SIP server register issue. - Enable 2nd subnet cause 1st subnet NAT can not communicate with WAN. - UDP fragment packets can't pass to WAN from LAN. - Sometime V2500Vi & V2510Vi ISDN detect issue when power on. ******************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : 2.5.8 Release Date : May 26, 2005 Applied Models : Vigor2500V series ( Vigor2500V, Vigor2500Vi, Vigor2510V, Vigor2510Vi) ******************************************************************************************** [1. New Features] - First release for Vigor2510V and ISDN models Vigor2500Vi/Vigor2510Vi. - Support Dail-Plan Utility version 1.0 and above. - Support US/UK/Denmark/Netherlands/Italian/German and user defined Tone/Caller ID settings. - Add telnet command "voip dsp micgain" and "voip dsp spkgain" for microphone and speaker gain control. [2. Enhancement] - Correct MPoA problem in Quick Start Wizard. - Correct Static Route problem. ******************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : v2.5.7 Release Date : December 29, 2004 Applied Models : Vigor2500V series ******************************************************************************************** [1. New Features] - Add Dail-plan telnet command to support dail-plan utility. - Allow inputting DNS server in MPoA setting. [2. Enhancement] - Resolve the browsing problem from UPnP InternetGatewayDevice in My Network Places. - Enhance the DMZ setting for WAN IP Alias. - Increase priority for local service ( Ex. VPN, RADUIS ) and avoid the the port of service will be added in the Open port or DMZ setting. - Resolved VPN passthrough issue. - Improve handling malformed DNS packet or MX type DNS query. - Improve DMZ host under heavy traffic. - Improve L2TP performance. - Fix the problem which can't hang up a VoIP call to mobile phone for some ITSP. ******************************************************************************************** Release Notes for Vigor2500V Series Firmware Version : v2.5.6 ( first release for the product new launch) Release Date : September 16, 2004 Applied Models : Vigor2500V series ******************************************************************************************** [Introduction] The Vigor2500V series ADSL VoIP router is a new product family which includes Vigor2500V, and Vigor2500Vi model. This product family is based on same hardware architecture of the whole Vigor 2500 series router and we integrate VoIP function into the router. Benefits of Vigor2500V ADSL VoIP Router --ADSL router for sharing your Internet connection --Robust firewall to help protect your computers --Make/Receive Voice calls over your ADSL connection using a regular telephone handset --Integration with your existing phone line (POTS) with automatic failover during power cuts --Free Voice-over-IP phone calls to other VoIP users --Compatible with Windows & Mac OS For more details of the product information, please visit our websites on http://www.draytek.com/ [Release Firmware] the same firmware for annex A and B 1> "v25vc256.xxx" is with Conexant modem code v3.27. ( recommended for annex A [POTS] ) 2> "v25vo256.xxx" is with Conexant modem code v3.20. ( recommended for annex B [ISDN] users who stay in Portugal, the Netherlands, Spain, and so on. ) ( For annex A users who stay in China, Australia and the USA. ) 3> "v25va256.xxx" is with Conexant modem code v3.46. ( Try this if you have sync problem on adsl. ) Notes: 1. You have to upgrade "*.RST" firmware file once you face the booting problems after upgrading. After upgrade "*.RST" firmware file to the router, it will erase the existing settings of the router, and restore the factory default settings into the router. What is the timing to using "*.rst" file to upgrade your router? Once you failed to upgrade your router using "*.ALL" firmware file (normally use) several times, then we suggest you use "*.RST" firmware file to do the upgrade. 2. After upgrade the router successfully, you can make sure the upgraded firmware version is the one listed above from the router's web user interface. 3. Do not attempt to restore old settings from a configuration backup file downloaded from previous firmware version. 4. Please select modulation to "MULTI" or "T1.413" when your adsl line was annex B ( ADSL Over ISDN) and it only can work with Alcatel ETSI Mode. 5. Please try to use modem code v3.20/3.46 if you meet sync problem. [END oF FILE]